日本一卡二卡四卡无卡乱码视频免费,国产女人aaa级久久久级,亚洲国产在一区二区三区,性色av免费网站

泰安揚帆數控科技有限公司為您提供等相關信息發布和資訊展示,敬請關注!
咨詢服務熱線:
13345281377

新聞資訊

產品

公司新聞

自動點焊機在使用中的作用

來源:http://niuniury.com/  發布時間:2023-09-08 瀏覽次數:0

在自動點焊機的焊接過程中,普遍存在的問題是:焊點在焊接過程中不能熔透而產生飛濺,導致點焊機的焊接質量不佳,因此在實際應用中應注意:
In the welding process of automatic spot welding machines, a common problem is that the welding points cannot melt thoroughly and produce splashes, resulting in poor welding quality. Therefore, in practical applications, attention should be paid to:
一、焊接點沒有穿透,熔核沒有形成或形成不好的形成。
1、 The welding point did not penetrate, and the fusion nucleus did not form or formed poorly.
1、無滲漏,即點焊時,無“豆?fàn)?rdquo;熔核排列。這個缺陷是很危險的,它會極大地改變焊接強度。
1. No leakage, that is, during spot welding, there is no "bean shaped" arrangement of molten nuclei. This defect is very dangerous as it will greatly alter the welding strength.
2、對焊接參數進行調試。若校驗確認參數無問題,則需檢查主電源電路,如:電源是否充足,是否損壞焊接變壓器等。
2. Debug welding parameters. If the calibration confirms that the parameters are correct, it is necessary to check the main power circuit, such as whether the power supply is sufficient and whether the welding transformer is damaged.
山東數控焊接設備
二、自動點焊機數量過多。
2、 There are too many automatic spot welding machines.
1、檢查支架與機體的絕緣電阻是否不良,是否形成局部短路。
1. Check if the insulation resistance between the bracket and the body is poor and if there is a local short circuit.
2、檢查觸點表面,如銅的撓性接縫,是否被嚴重氧化,觸點電阻的形成,會加重發熱。
2. Check if the contact surface, such as the flexible joints of copper, is severely oxidized, and the formation of contact resistance can exacerbate heating.
3、檢查焊縫的厚度及負載的連續性是否符合要求,焊機是否過熱。
3. Check whether the thickness of the weld seam and the continuity of the load meet the requirements, and whether the welding machine is overheating.
4、檢查進水壓力、水量和供水溫度是否適當,系統是否被污物所隔開,這些污物會由于冷卻不佳而導致電臂過熱。
4. Check whether the inlet pressure, water volume, and water supply temperature are appropriate, and whether the system is separated by dirt, which can cause overheating of the electric arm due to poor cooling.
三、焊接時產生的意外飛濺。
3、 Unexpected spatter generated during welding.
1、檢查電流是否過大或過低的壓力。
1. Check if the current is too high or the pressure is too low.
2、焊接工件的強度不足:焊接電流越來越小,而且焊接現象也不強。
2. The strength of the welded workpiece is insufficient: the welding current is decreasing, and the welding phenomenon is also not strong.

上一篇:壓力容器自動焊機焊接接頭性能的要求有哪些?
下一篇:激光焊接機在日常延長機器壽命方法

国产白丝护士AV在线网站| 国产成人av免费网址| 又黄又爽又色又刺激的视频| 少妇又紧又色又爽又刺激视频| 国精产品一区二区三区| 曰批免费视频播放免费直播| 国产成人精彩在线视频| 亚洲人成色7777在线观看不卡| 亚洲AV无码一区二区三区天堂| 成人免费无码av| 国产人久久人人人人爽| 国产无吗一区二区三区在线欢| 日本视频网站www色高清免费| 亚洲国产精品久久一线不卡| 精品久久久久久久久久久aⅴ| 国产激情久久久久久熟女老人| 国产av午夜精品一区二区入口| 欧产日产国色天香区别视频| 亚洲AV成人无码一区二区三区在线观看 | 亚洲精品中文字幕乱码| 日韩精品无码一区二区三区| 欧美日韩精品一区二区在线观看| 女女同性AV片在线观看免费| 蜜臀久久久久精品久久久| 亚洲亚洲人成综合网络| 无码精品人妻一区二区三区涩爱| 国产精品美女久久久久av爽| 国产偷国产偷亚洲高清人| 少妇人妻偷人精品视频| 亚洲国产一区二区三区亚瑟| 精品卡一卡二乱码新区| 被黑人猛烈30分钟视频| 免费观看黄a级毛片| 国产成人午夜高潮毛片| 欧美黑人又粗又大XXX| 亚洲色成人网站www永久| 午夜精品久久久久久| 欧美黑人巨大videos极品| 欧美xxxx黑人又粗又长精品| 特色特黄A毛片高清免费观看| 久久久久久精品久久久久|