如果你在使用山東數控焊接設備中遇到了相關問題，可以參考解決，接下來我們來看看在使用設備時要注意哪些?

If you encounter relevant problems in using Shandong CNC welding equipment, you can refer to and solve them. Next, let's take a look at what you should pay attention to when using the equipment?

1.操作機器的人員一定要熟悉設備的結構以及工作原理和操作方法。

1. Personnel operating the machine must be familiar with the structure, working principle and operation method of the equipment.

2.機器操作人員不能戴手套進行操作，女工長發應盤起，不許穿太過寬松的衣服，不準接觸皮帶，傳動部分，刀片等，防止傷人。

2. The machine operator shall not wear gloves for operation. The long hair of the female worker shall be rolled up. It is not allowed to wear too loose clothes. It is not allowed to touch the belt, transmission part, blade, etc. to prevent injury.

3.機器開機前，應檢查送紙臺面有無放置工具或其它雜物，每次開機時一定要先按電鈴，有了本機別的操作員工響應后，方可開機。如果按完電鈴后不開車，過一段時間再開車要再按電鈴，確認沒有問題后再進行運轉。啟動機器不準直接高速運轉，需從速度零開始，逐漸通過速度旋鈕達到額定工作速度。

3. Before starting the machine, check whether there are tools or other sundries on the paper feeding table. Each time you start the machine, you must press the bell first. The machine can only be started after other operators respond. If you do not start the car after pressing the bell, you should press the bell again after a period of time to confirm that there is no problem before starting the car. It is not allowed to start the machine directly at high speed. Start from speed zero and gradually reach the rated working speed through the speed knob.

4.開槽部分要按程序操作，開槽刀和分紙刀的刀口都很鋒利，ji易傷手;開槽上刀一定要落在下刀槽里，處于正中位置調好刀后一定要鎖好緊固螺絲，并要注意把鏟紙刀放入鏟紙槽里，四刀聯動調好后也要記得鎖緊螺絲，各部調好鎖緊后先用手柄轉動開槽部幾圈，如無異常現象方可繼續操作設備。在高速運轉時，稍不留神手就會碰到鋒利的刀口上，特別要當心。在生產時，如果違反操作規程也很容易造成傷害事故，所以也要注意。

4. The slotting part shall be operated according to the procedure. The cutting edges of the slotting knife and the paper separating knife are very sharp, which is easy to hurt hands; The slotting upper knife must fall into the lower knife slot. When the knife is in the center position and adjusted, the fastening screw must be locked. Pay attention to putting the paper shoveling knife into the paper shoveling slot. Remember to lock the screw after the four knife linkage is adjusted. After each part is adjusted and locked, use the handle to rotate the slotting part for several turns. If there is no abnormal phenomenon, continue to operate the equipment. When running at high speed, you will touch the sharp edge if you don't leave your mind. Be careful. During production, it is also easy to cause injury accidents if operating procedures are violated, so attention should also be paid.

技術人員在使用自動焊接設備時，一定要注意以上幾點內容，不要因?yàn)橐粫r(shí)的粗心引發事故，如果出現了一些常見問題，可以根據實際情況進行維修，自己維修不了，可以找相關的維修人員處理。更多相關內容就來我們網站http://niuniury.com咨詢吧！

When using automatic welding equipment, technicians must pay attention to the above points. Don't cause accidents due to carelessness. If there are some common problems, they can repair them according to the actual situation. If they can't repair them themselves, they can find relevant maintenance personnel to deal with them. More relevant content will come to our website http://niuniury.com Consult!